Program tasks are flexible: you can set multiple zones to turn on at the same time, and you can have the same zone turn on multiple times in different tasks. First append a new task, then click a zone to enable or disable that zone from the task, and finally set the duration. Each program consists of a number of program tasks. The program editing interface (shown on the left) allows you to change the program name, configure it as a weekly or interval program, set odd/even day restrictions, set the first start time and additional start times. Back to the homepage, click on a Program button (the black-colored button creates a new program, and blue-colored buttons are existing programs) to add a new program or edit an existing program. Again, the default device key is opendoor. At the homepage, you can also click on “Manual” to open the Manual Control page, where you can start a test program or any of the existing programs. Click on “Settings” at the lower-left of the homepage, this will open the Settings/Options page (middle image above), where you can configure the time zone, device name, zone name, and other options. The Homepage (left image above) shows the current time, status of each zone, and buttons that lead to other pages. The default device key is opendoor, which you can change in Settings. Open a browser and type in the IP address, it should open OSBee’s homepage show below. This IP address is printed on the LCD screen at the bottom. In WiFi station mode, OSBee obtains an IP address from your home WiFi router. If you want to change the WiFi network, you can perform a factory reset and it will go back to AP mode. From now on, it remembers your WiFi and will always attempt to connect to it when it’s powered on. At this point, OSBee will attempt to connect to your WiFi, and if successful, it will reboot itself, and now WiFi configuration is complete. If you have already created a Blynk app token (see Section 5), you can also paste it here, otherwise, just leave the token blank. So choose, or directly type in your home WiFi’s SSID and WiFi password (Note: it only connects to 2.4G WiFi). The main purpose of the WiFi configuration is to let OSBee know your home WiFi’s name and password, so that it can subsequently connect to your WiFi. This should open the WiFi configuration page. Once connected, open a web browser on your phone (or laptop) and type in the IP address 192.168.4.1. Use your smartphone, or laptop to connect to this WiFi SSID (there is no WiFi password). In this mode, OSBee creates a WiFi SSID, the name of which is printed on the LCD screen (e.g. The first time you power on OSBee, or after each factory reset, the controller starts in AP (Access Point) mode. OSBee is powered by a USB adapter through a microUSB cable. Un-tighten a screw, insert the wire through the opening below it, wrap the wire around the screw, then tighten the screw. At the back of the controller there are four big screws. The positive (+) wire (often colored red) of each valve should be connected together and go to the COM terminal the negative (-) wire (often colored black) of each valve should go to an individual zone (1, 2, or 3). You can control your device from outside the local network with proper port forwarding and use of the WAN IP within the application or by using a VPN.OSBee has four terminals marked COM (common), Z1 (zone 1), Z2, and Z3. This application requires you to own an OpenSprinkler that is properly connected to your network. * Multiple supported languages (Afrikaans, Amharic, Chinese, Czech, Dutch, French, German, Hebrew, Hungarian, Italian, Mongolian, Norwegian, Polish, Portuguese, Slovak, Slovenian, Spanish and more) * View current weather and forecast status for the device location * View graphical and tabulated representation of log data * View visual representation of upcoming scheduled programs * Launch ad-hoc or defined programs instantly OpenSprinkler is an open-source Internet web-based sprinkler timer / controller built upon the Arduino platform. The application allows you to automatically detect and control your OpenSprinkler irrigation system(s).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |